See:
Participation in Forum on September 6, 2021
Another suggestion for PPLA is: 1) The DRUM COATER of the feed zone packaging system should be installed directly above the SURGE HOPPER of the packaging machine. 2) The bulk loading area should be installed under the bulk bin. The reason is to reduce the generation of pellet powder. And to get rid of pollution. THANKS, CHOI
1
Participation in Forum on July 20, 2021
I would like to propose my opinion to all interested parties as follows. I also think that the grinding process is very important. The reasons are 1) the generation of powder in the feed 2) the decrease in moisture in the grain 3) the particle size preference of animals. -For pellet feed, a 2.4 mm screen for corn and a 2 mm screen for wheat should be selected and the other stripping grain 3.2 ...
0
Participation in Forum on June 22, 2021
My suggestion is also highly recommended for post-pellet liquid application. However, when applying PPLA, DRUM COATER must be selected when selecting the coating machine. The reason is to reduce the generation of powder.This is because other COATING MACHINE, PADDLE TYPE or RIBBON TYPE increases PELLET powder.THANKS, CHOI.
2
Participation in Forum on June 4, 2021
PS: It must be supplied directly from the feed mill to the farm. You must never do this before being transferred to another BULK CAR in the middle before arriving at the farm. Thanks, CHOI
0
Participation in Forum on June 4, 2021
I propose to you as follows for the transport of pig feed from the feed mill to the farm with the following contents. 1) Naturally, the CV in the formulation should be less than 4, and there should be no contamination of the drug. 2) There should be no separation of powder or contamination until bulk bean after mixing. 3) There should be no separation of feed when loading pig feed from the bulk bi ...
1
CHOI, YOUNGSOO likes the video:
Dr. Cassie Jones (Kansas State University) discusses feed control and virus prevention, in this Swine It interview with host Márcio Gonçalves.
Participation in Forum on March 30, 2021
For me, the particle size of raw materials is very important when producing pellets. Also, the pellet size is very important. So, I propose as follows. 1. The blending ratio must also be good. 2, the combination should also be good. (My suggestion is that the CV should be less than 4.) 3. The particle size should be less than 700 microns for all raw materials. For Grinding, a 2.4 mm screen for ...
8
Participation in Forum on March 6, 2021
Hi ! Do you know rice cooker for cooking rice, it's the same as cooking corn for flakes added steam around 5.5 -6 %, . In Korea, it is temperature around 100-104 degree c, also, cooking times around 15 minutes, there are feed plants that operate three chambers two-ton cooking chambers and this aadeed steam steam pressure around 2 kg/cm2. PSIG. Thanks, Choi
0
Participation in Forum on March 5, 2021
CHOI, YOUNGSOO The operation was sent to the pelleting. Sorry. In Korea, corn fracking is operated as follows. 1. In Korea, without using GRAVITIY FLOW TYPE, cook 5-6% (100 -120 KG) of corn and steam of 2 tons X 2 of COOKING CHAMBER and 2 KG/CM2 of steam for about 15 minutes. It produces approximately 10 tons with an oil pressure of 400 # with MM-1.2 MM, and is produced by controlling moisture to ...
0
Participation in Forum on March 5, 2021
Kulvir Aulakh My suggestion is below. 1. You must determine the PDI of the pellet. 2. The pellet die L/d should be determined accordingly. 3. Water addition should be decided according to the plugging of the pellet die. 4. The feed retention time of the conditioner should be at least 30 seconds and the filling rate should be 50%-70%. 5. Check the dry mash and wet mash moisture content of the feed ...
0
equalizer Statistics: Forums(17)
Information
Location:Gyeongsan, Kyongsang-bukto, North Korea
Profile: Professional
Followers (2)